The active control of macrofiber composite over harmonic vibration of arcplate structures
Jianhui Wei^{1} , Weiping He^{2} , Jianwei Tu^{3} , Jiarui Zhang^{4} , Wei Luo^{5}
^{1, 2}Wuhan 2nd Ship Design and Research Institute, Wuhan, China
^{3, 4, 5}Hubei Key Laboratory of Roadway Bridge and Structure Engineering, Wuhan University of Technology, Wuhan, China
^{3}Corresponding author
Vibroengineering PROCEDIA, Vol. 14, 2017, p. 167171.
https://doi.org/10.21595/vp.2017.19160
Received 11 September 2017; accepted 19 September 2017; published 21 October 2017
JVE Conferences
This paper offers an actuating equation for MFC arcplate structures to obtain MFC’s accurate actuating force and actuating bending moment to areplate structures and increase MFC control effect on vibration. This paper proposes the P1 type MFC arcplate actuating equation which considers the recombination action of MFC and controlled structure, and arcplate curvature influence on MFC, obtaining the MFC actuating force and actuating bending moment for arcplate structures. The vibration control experiment of MFC arcplate structures is performed, and the deviation between finite element simulation results adopting this equation and the experimental data is less than 8.5 %. The research shows that the P1 type MFC actuating equation deduced in this paper is correct and fully applicative to the MFC vibration control simulation to arcplate structures.
Keywords: macrofiber composite (MFC), actuating equation, finite element analysis, arcplate structure.
1. Introduction
Currently, the widely used piezoelectric materials include piezoelectric crystal and piezoelectric ceramics which, however, as fragile materials with poor flexibility and elasticity, cannot bend and be applied to curved surface structures such as sphere or cylinder. To solve this problem, domestic and overseas scholars have developed a new type of piezoelectric material – macro fiber composite (MFC) which makes piezoelectric ceramics fibrous and then recombines it with organic polymer matrix according to different connection methods, volume ratios, and spatial distribution [1].
To conduct vibration control over arcplate structure with MFC, MFC electromechanical coupling relationship is supposed to be understood to deduce the actuating equation of MFC arcplate structures. Many scholars have studied MFC actuating equation recently. ShunQi Zhang et al. [2] have established the finite element model pasted with MFC cantilever by applying the linear piezoelectric constitutive equation based on ReissnerMindlin theory, and studied the impact difference on cantilever deformation made by different arrangement modes of piezoelectric fibers under normal pressure. In allusion to the vibration created by the axial movement of cantilever, Guoliang Ma et al. [3] have deduced the free vibration equation about cantilever axial movement with Hamilton theory. They have considered MFC and the major structure separately and treated MFC impact on the major structure as external controlling force, thus simplifying the actuating equation and offering new thoughts for the research about MFC actuating equation. M. L. Dano and B. Jullière [4] have conducted active control over the thermalinduced deformation of cantilever with MFC and performed composite structure modeling and the experiment with finite element software, indicating that MFC has a remarkable effect on reducing the thermalinduced deformation of cantilever.
Based on those studies, this paper deduces the actuating equation which considers the recombination action between MFC and the controlled structure and the actuating force in the radial direction made by MFC influenced by the arcplate curvature. The vibration control simulation over arcplate structures and active control experiment are accomplished on the basis of the equation.
2. The actuating equation of MFC arcplate structures
The twodimensional constitutive equation of MFC linearelastic piezoelectric material polarized in the direction of $x$ axis is written as:
where, ${s}_{ij}^{E}$ is the flexibility coefficient of MFC, in which $i$ represents the MFC strain direction, and $j$ the MFC stress direction; ${d}_{ij}$_{}is the piezoelectric strain coefficient of MFC, in which $i$ represents the direction of electric field action, $j$ the strain direction of piezoelectric material after electric field action, 1, 3 correspond to $z$, $x$ directions respectively in Cartesian coordinate system; ${E}_{x}$ is electric field intensity in $x$ direction.
As is shown in Fig. 1, the thickness of twodimensional MFC arcplate structure is $H$; MFC effective length is $a$, width $b$, and thickness $h$; $L$ is the surface distance between the structural neutral axis and the controlled structure. Since MFC thickness is extremely small, it is approximately assumed that $L=0.5H$.
From Eq. (1) the twodimensional MFC stress is:
in which ${\mu}_{f}$ is MFC Poisson’s ratio; ${E}_{f}$ is elasticity modulus of MFC.
The actuating bending moment of MFC per unit length for twodimensional arcplate structure is:
According to deformation theory, the strain of twodimensional MFC structure can be represented by bending moments ${M}_{x}$ and ${M}_{z}$:
in which ${E}_{p}$ is elasticity modulus of the controlled structure; ${I}_{p\theta}$, ${I}_{pz}$ the inertia moments of arcplate intersecting surface coiling MFC horizontal and vertical neutrospheres respectively.
By substituting Eq. (4) into Eq. (3), it is obtained that:
in which:
Therefore, the actuating force of MFC is:
in which $R$ is the radius of arcplate, and $\gamma $ is the radian occupied by MFC.
Fig. 1. The unit structure of MFC arcplate
Fig. 2. ANSYS model of MFC arcplate structure
3. The experimental verification of the actuating equation of MFC arcplate structures
To verify the correctness of the equation, the P1/${d}_{33}$ type MFC is attached to the arcplate structure to perform analogue simulation and vibration control experiment.
Table 1. Material properties
Material

Arcplate (aluminum)

Elasticity modulus

70.5 GPa

Density

2700 kg/m^{3}

Poisson’s ratio

0.30

Width/Span

350 mm

Width

400 mm

Thickness

2 mm

Height

55 mm

To begin with, the arcplate structure is modeled with ANSYS, whose parameters are shown in Table 1. Then the exciting force, MFC actuating force and actuating bending moment are defined, the exciting position located in the center of the arc plate and MFC actuating position at the red lines in Fig. 2. The obtained ${F}_{\theta 0}$, ${F}_{z0}$ and ${M}_{x0}$, ${M}_{z0}$ are applied at the node located at the red lines in Fig. 2, and the obtained actuating force in the radial direction ${F}_{r0}$ at each node surrounded by the red lines. In analogue simulation, the exciting force and MFC actuating force are both simple harmonic force and the exciting force is opposite to the displacement phase produced by MFC actuating force and actuating bending moment. In this paper, the exciting force includes three working conditions: 20 Hz, 10 N; 50 Hz, 10 N; and 100 Hz, 10 N, and MFC working voltage is 300 V.
Fig. 3. Experimental system of MFC arcplate
Fig. 4. Experimental model of MFC arc plate
In vibration control experiment of MFC arc plate, the arc plate and MFC parameters are consistent with simulation. The key instruments include acceleration sensor, MFC, exciter, power amplifier, and dSPACE realtime simulation system which is shown in Fig. 3. Three sinusoidal signals are output by dSPACE (20 Hz, 50 Hz and 100 Hz) to provide the exciter and MFC with exciting signals, and the signal phase of the exciter is opposite to that of MFC. The experimental model is illustrated in Fig. 4.
Fig. 5. Acceleration comparison of simulation and experiment before and after control under 20 Hz, 50 Hz, 100 Hz excitement
a) Acceleration comparison before and after 20 Hz arcplate control
b) Acceleration comparison before and after 50 Hz arcplate control
c) Acceleration comparison before and after 100 Hz arcplate control
In Fig. 5, acceleration time courses of analogue simulation and actual test are compared under different working conditions. It is evident that under three different working conditions, the deviation of simulation and experiment is less than 8.5 %, so the actuating equation deduced in this paper can correctly depict the strength and electricity relationship of MFC. When the exciting force is 20 Hz, 10 N and working voltage is 300 V, the monolithic MFC in the experiment can decrease acceleration amplitude by 9.54%; when the exciting force is 50 Hz, 10 N and the working voltage is 300 V, the monolithic MFC can decrease acceleration amplitude by 12.68 %; when the exciting force is 100 Hz, 10 N and the working voltage is 300 V, the monolithic MFC can decrease acceleration amplitude by 15.44 %. As a result, MFC can effectively decrease the vibration of arcplate structures, esp. the highfrequency vibration.
4. Conclusions
This paper deduces the actuating equation of MFC arcplate structures and verifies it through simulation and experiment, drawing the conclusions as follows:
1) The equation deduced in this paper considers the recombination action of MFC and arcplate structures and the actuating force in the radial direction made by MFC under the impact of the arcplate curvature, which indicates that MFC electromechanical coupling relationship for the arcplate is more accurate and practical.
2) This paper describes the MFC active vibration control simulation and experiment for arcplate structures. The research not only proves that the actuating equation proposed in the paper is correct and applicative to arcplate structures, but also indicates that MFC has a good effect on vibration control of arcplate structures.
Acknowledgements
This research work is supported by the Chinese National Natural Science Foundation, Project No. 51478372, Hubei Province Innovation Group Project, Project No. 2016CFA020 and the Fundamental Research Funds for the Central Universities, Project No. 2017zy055.
References
 Williams B. R., Park G., Inman D. J., Wilkie W. K. An overview of composite actuators with piezoceramic fibers. Proceedings of 20th International Modal Analysis Conference, 2002, p. 421427. [Search CrossRef]
 Zhang Shun Qi, Li Ya Xi, Schmidt Rüdiger Modeling and simulation of macrofiber composite layered smart structures. Composite Structures, Vol. 126, 2015, p. 89100. [Publisher]
 Ma Guoliang, Xu Minglong, An Zengyong, Wu Chengsong, Miao Weikai Active vibration control of an axially moving cantilever structure using MFC. International Journal of Applied Electromagnetics and Mechanics, Vol. 52, 2016, p. 967974. [Publisher]
 Dano M.L., Jullière B. Active control of thermally induced distortion in composite structures using macro fiber composite actuators. Smart Materials and Structures, Vol. 16, 2007, p. 23152322. [Publisher]
Cited By
Composite Structures
Jarosław Gawryluk, Andrzej Mitura, Andrzej Teter

2020

3RD NATIONAL CONFERENCE ON CURRENT AND EMERGING PROCESS TECHNOLOGIES – CONCEPT 2020
Gawryluk Jarosław, Mitura Andrzej, Teter Andrzej

2020
